Cable Installation Tools swivel lug type pullers multi puller multiple duct installations DUB-Wise Puller Duct Duct Installation cable installtion tools manhole products lubricant

The 00619 Poly Puller is a new puller introduced by DCD and has features that make it a very different puller than others on the market. Most obvious is the Polyurethane nose cone - this material has proved to be extremely durable during field testing. This puller will also cover a larger range of bore sizes compared to the 00620 series. It comes standard with a Duct Plugger as well as a rear pulling eye. Standard Duct Sleeves (00625 series) can also be used with this product.

The 00619 Series duct puller together with the 00620 & 00621(Metric) Series of duct pullers are designed to grip polyethylene ducting using expanding jaws to grip the inside wall of the duct. This causes the pulling load to be spread around the circumference of the duct and allows a maximum load to be applied without damage to the ducting.

Care should be taken at all times not to exceed the yield value of the ducting since this may cause permanent deformation to the duct as well as loss to the integrity of the polyethylene.

On thin wall ducting, it is recommended that an outer Duct Sleeve be used to prevent the duct from stretching during installation. You could also choose to use the DUB-Wise with a built in outer sleeve. A firmer and more stable grip will also be obtained when this is done.

Use of a Duct Plugger will help prevent mud and slurry from entering past the puller into the ducting.

These Duct Pullers are installed quickly and easily and require no special tooling.

Duct wall (applicable on the 00619 & 00620 imperial sizes) thickness is normally designated by an SDR value. The lower the SDR value, the heavier the wall thickness. These products can be used on SDR 11 through SDR 17 ducting.

When ordering 10" or 12" Duct Pullers, the SDR value of the Duct must be specified. Additional jaw sets are available for SDR 9, SDR 11 and SDR 17 and can be purchased separately to modify the puller. Inquire for part numbers.

Metric duct wall thickness (00621 series) is normally designated by a PN value. The lower the PN value, the heavier the wall thickness. These products can be used on PN6 through PN10 ducting.

Key Benefits

Duct Puller Part#	Nominal Duct Diameter	Safe Working Load 3:1 Underground	Minimum Duct Inside Diameter	Maximum Duct Inside Diameter	Net Weight	Duct Sleeve Part#	Duct Plugger Part#
00621-040	40 mm	16 kN.	32.5 mm	38.1 mm	0.7 kg	00626-040	00631-040
00621-063	63 mm	27 kN.	50.8 mm	57.1 mm	1.5 kg	00626-063	00631-063
00621-075	75 mm	27 kN.	60.3 mm	66.7 mm	2.4 kg	00626-075	00631-075
00621-090	90 mm	53 kN.	73.0 mm	81.0 mm	4.2 kg	00626-090	00631-090
00621-110	110 mm	53 kN.	85.7 mm	100.0 mm	6.7 kg	00626-110	00631-110
00621-125	125 mm	113 kN.	98.8 mm	111.5 mm	14.5 kg	-	00631-125
00621-140	140 mm	113 kN.	114.0 mm	127.0 mm	15.4 kg	-	00631-140
00621-160	160 mm	113 kN.	125.4 mm	142.9 mm	23.5 kg	-	00631-160
00621-180	180 mm	113 kN.	144.5 mm	162.0 mm	32.8 kg	-	00631-180
00621-200	200 mm	164 kN.	163.5 mm	200.0 mm	43 kg	-	00631-200